INSTALLATION
Step one – CleaningImportant, clean up the mounting surface before mounting. Make use of soapy that is warm very very first to remove all wax and dust. Dry entirely and clean once again employing a cleaner. Usually do not touch area after cleansing.
Step two – Marking the Mounting Location
1. Usually do not remove adhesive tape backing until following the mounting location was marked tape that is using. First keep the -light club construction in place so it is similarly spaced all the way through and left to appropriate. (see Figure 2a.)
2. The cable bundle end regarding the light club needs to be toward the motorist’s part to allow the turn signals be effective precisely. Mark this location with three strips of tape, spot tape so top side of tape could be the center (top to botom) of recessed area (see Figure 2b).
3. The edge that is top of tape strips should line-up because of the bottom side of the light club (see Figure 2c). NOTE: On Ford F150 trucks the bottom of the light club construction is based with a sheet steel ridge in your body. Just part centering dimensions are expected.
4. After eliminating the light club installation, be sure that the most effective side of all three tape strips have reached the same height. Accurately determine the side-to-side location by very first marking the vehicle centerline regarding the center tapestrip (see Figure 2d).
5. Measure to your remaining 30 ins from centerline and mark this location in the tape that is left (see Figure 2e). The remaining end of this light club installation will begin only at that mark that is left therefore the bottom side of the tight club is supposed to be put into line utilizing the top side granny hookup sites of the tape strip.
Step Three – Mounting Installation
1. Peel off the adhesive tape backing while being careful not to contaminate the adhesive area with finger marks or dust. During the driven part pre-rnarked location, gently connect the light bar in the noticeable tape for the left to right centering. Make certain edge that is bottom of club is in-line with all the top side of tape. AT THE MOMENT CANNOT APPLY A WHOLE LOT OF STRESS – you might adjust the alignment of this light club later on.
2. Gently connect the center area of the light club at its noticeable location, and lastly the right part. In the event that light club is certainly not right and degree, pull within the adhesive taped areas lightly and reposition (see Figure 3a).
3. Eliminate location tape strips (see Figure 3b).
Move 4 – Activating the Tape to advertise Comprehensive Bond 3M’s Technical Sheets for VHB tape need that at the least 15 pounds of force should be placed on item. We advise utilizing the synthetic or lumber handle of any device and press securely across the light club at tape locations that are adhesive. DON’T PRESS FROM THE EVIDENT LED LIGHT STRIP. VHB tape will gain 50% of energy in 20 moments and completely relationship in 3 days (at conditions of 15В°C or maybe more).
Move 5 – Electrical Hook-Up
1. Utilize the provided tie wraps to carry the wire bundle up and away from view behind the bumper. Plug the connector into the automobiles standard flat trailer that is four-pin connector when it is available on your own automobile. A widely available adapter can be purchased to convert it to a flat four-pin connector if your vehicle has a round four-pin trailer light connector.
2. In the event your car doesn’t have a trailer light plug, you can easily clip from the light club four-pin connector and difficult cable the leads straight to the automobile taillights utilizing the information in Figure 4. The park lead that is light usually the one straight beside the ground.
3. a vehicles that are few various light light light bulb filaments for stoplight and change signals. In cases like this a acquireable adapter is needed to get from the five-wire system production to a typical four-wire trailer light input. An alternative choice in this situation will be connect the remaining and wires that are right in Figure 4 and link them to your automobile brake light wire. Should this be done, just the light club running lights and brake light function will run and never the change signals.
First link the flat four connector and white reverse light cable as previously mentioned when you look at the included instruction sheet then stick to the supplemental guidelines below:
The residual RED wire requirements to get in touch to a consistent вЂhot’ 12V energy supply for instance the cable coming off either your Ignition or Accessory Terminal where your ignition key gets into your automobiles steering column. Many model that is late have actually sufficient room underneath the dashboard in the motorist part where you are able to access those two ignition/accessory wires. The wire that is RED get in touch to one of the two wires otherwise the Xtreme light bar will not work correctly.
After you have followed the guidelines regarding the very first installation instruction sheet, just difficult cable (aka splice) the white cable appearing out of the RECON LED tailgate club directly to the postive cable of your drivers side reverse light. This cable are available simply by eliminating your drivers tail light lens and after the two cables for the light that is reverse. The negative is usually black colored. Splice in to the other cable which can be the wire that is positive.
